Comparing cohorts fairly in Charts: incomplete periods and Conversion Timeframes
A conversion chart can make an old cohort look strong and a new one look weak for a boring reason: the older group simply had more calendar time to act. Charts addresses that with two additions — visual styling for periods that have not finished maturing, and a Conversion Timeframe selector on the Initial Conversion and Conversion to Paying charts. This guide explains what each control does, which chart types use which maturity rule, and how to set a timeframe before you draw conclusions.
Why cohort timing distorts a chart
Charts automates reporting across more than 15 metrics, including monthly recurring revenue and how it moves, subscriber retention, and conversions. Comparing cohorts on those metrics is where the timing problem shows up.
Consider a group that installed a year ago against one that installed last month. The first group has had twelve months to convert; the second has had roughly one. If you plot raw conversion counts side by side, the older group will usually appear to perform better — not necessarily because it converts at a higher rate, but because it had twelve times the window. Any comparison that ignores elapsed time is measuring the calendar as much as the product.
The two additions below exist to remove that distortion from the reading, not to change the underlying data.
Incomplete period styling: what the marks mean
Periods where cohorts have not fully matured are now drawn distinctly. Depending on the chart type, an unfinished period appears with dashed lines or semi-transparent areas; in the accompanying data table, the matching cells carry a hashed overlay. The marks are a reading aid — they tell you the value is still filling in.
What counts as incomplete depends on how the chart is cohorted:
- Cohorted by event date: the incomplete period is the current day, week, month, or year, whichever resolution the chart uses.
- Cohorted by a customer's first seen date, such as the Realized LTV charts: the incomplete period depends on the current day together with the Customer Lifetime you have set. That combination shows whether a period has had enough time to reach full maturity and be comparable with earlier periods.
The practical rule: before comparing two points, check whether either one carries the incomplete styling. If it does, you are comparing a finished result with a partial one.
Conversion Timeframe selection on conversion charts
The Initial Conversion and Conversion to Paying charts now let you choose a Conversion Timeframe. The setting caps how long a conversion may take and still count toward the chart, so every cohort is measured against the same window.
This mirrors the role the Customer Lifetime setting plays in the Realized LTV charts: it lets you line up earlier periods accurately and see at a glance whether your most recent periods are still incomplete. Equalizing the window matters most on conversion charts, because that is where a cohort's extra elapsed time most easily masquerades as better performance.
Once a timeframe is set, a recent cohort that looks behind an older one is a fairer signal — both had the same amount of time to convert.
Which control applies to which chart
Use this map to pick the right maturity control before reading a chart.
A short pre-read checklist
Run through these steps before you interpret a cohort comparison:
- Identify the cohorting basis. Is the chart cohorted by event date or by customer first seen date? That determines what "incomplete" means.
- Check the marks. Dashed lines, semi-transparent areas, or hashed table cells mean the period is still maturing — do not treat it as final.
- Set the window on conversion charts. Choose a Conversion Timeframe on Initial Conversion or Conversion to Paying so every cohort gets the same allowance.
- Match the LTV window. On Realized LTV charts, confirm the Customer Lifetime setting reflects the maturity you want to compare at.
- Compare like with like. Only after steps 1–4 should a gap between cohorts be read as a performance difference.
The goal of both additions is the same: make accurate performance comparisons easy enough that you can see what is actually driving the business and do more of it.
| Chart type | Cohorted by | What defines an incomplete period | Control you set |
|---|---|---|---|
| Charts cohorted by event date | Event date | The current day, week, month, or year, depending on resolution | None — determined by the current date |
| Realized LTV charts | Customer's first seen date | Current day combined with the Customer Lifetime setting | Customer Lifetime |
| Initial Conversion chart | Cohort | Conversions outside the selected window are excluded | Conversion Timeframe |
| Conversion to Paying chart | Cohort | Conversions outside the selected window are excluded | Conversion Timeframe |
Describes the feature as launched in the March 2023 announcement; chart behavior and available controls may have changed since. Confirm current behavior in the product documentation.
Frequently asked questions
Why does an older cohort look better than a recent one on a conversion chart?
The older cohort has had more time to convert. A group that is a year old has had twelve times the window of a one-month-old group, so raw counts favor it even when the underlying conversion rate is the same or lower. Setting a Conversion Timeframe equalizes the window so the comparison reflects performance rather than elapsed time.
What does a dashed line or semi-transparent area mean in a chart?
It marks a period where the cohort has not fully matured. Depending on chart type, unfinished periods use dashed lines or semi-transparent areas, and the matching data-table cells get a hashed overlay. Treat those values as still filling in.
How is an incomplete period determined for Realized LTV charts?
For charts cohorted by a customer's first seen date, including Realized LTV, the incomplete period depends on the current day and the Customer Lifetime you have specified. That lets you see whether a period has had enough time to reach full maturity before comparing it with earlier periods.
Which charts offer Conversion Timeframe selection?
The Initial Conversion and Conversion to Paying charts. The setting limits how long a conversion may take to still be counted in the chart.